Bloodhound diary: Getting the job done at over 600mph

Image copyright
BLOODHOUND LSR/Charlie Sperring

A British team is developing a car that will be capable of reaching 1,000mph (1,610km/h). Powered by a rocket bolted to a Eurofighter-Typhoon jet engine, the vehicle aims to show its potential by going progressively faster, year after year. Recent high-speed trials saw Bloodhound hit 628mph (1,010km/h). The next step would be to break the existing world land speed record (763mph; 1,228km/h). The racing is being conducted on Hakskeen Pan in Northern Cape, South Africa.

We did it! 628mph 1,010 km/h. Bloodhound exceeded all our expectations by blasting past 600mph and making it look easy.

However, just before we get carried away about how “easy” this sport of straight-line racing is, we did have to work quite hard in November to get this amazing result.

Things started well enough with rapid progress up to 500mph. As mentioned in last month’s diary, we were also getting on top of a couple of car handling problems.

After our initial testing, it became clear that we didn’t want to run the car in crosswinds above 10mph – fighting the steering at several hundred miles an hour convinced me of that quite quickly.

The other key problem we solved was making the brake chutes fly steadily behind the car, rather than oscillating from side to side. This was key to being able to go faster safely.

If the car needs to slow down quickly (see below…), the chutes are there to rescue it, so they need to make things better, not worse.

Image copyright

After hitting 501mph in early November, we were hoping for a couple more quick runs up through 550mph to 600+, to finish our high-speed tests. It wasn’t going to be that easy.

At the end of the 501mph run, the “Fire” caption had come on in the cockpit, indicating an engine bay overheat. Needless to say, I shut the engine down fairly quickly, just in case.

Bloodhound’s rescue crews were alongside the car within seconds, confirming that there was no sign of fire.

The heat detection system around the engine uses something called “fire wire”, which changes its electrical properties (resistance and capacitance) when it gets hot. However, the electrical properties will also change if the fire wire gets slightly damaged.

On close inspection, we found a small kink in the wire that could well have set off the warning. The wire was fixed and tested, and we were ready to go again.

On the next high-speed run a couple of days later, the Fire caption came on again, accelerating through 470mph. Within one second I had throttled back the engine, before deploying the brake chute, which flew rock-steady behind the car – this is the time when it needs to be working perfectly!

Once again, no signs of fire, so we had to look deeper with a full strip down of the rear end of the car. More fire wire damage was found and sorted.

The temperature stickers inside the engine bay also showed local overheating, requiring some simple modifications. This is all part of test-and-development engineering: it’s what this year’s high-speed test session was all about.

Image copyright
Bloodhound LSR

Image caption

Hot stuff

After these minor interruptions, the car behaved perfectly. Four more runs were needed, two with the airbrakes deployed (which work better than expected – good news!) and two at high speed to complete the testing.

The final run was meant to hit just over 600mph, but it didn’t quite work out like that. The calculated distance for the acceleration was just under 4.5 miles (7km), so “Rescue 1” was positioned at km 7 to make a radio call as I went past, backing up the in-cockpit distance readout. As I went blasting past the km 7 mark, I heard the call from Rescue 1.

The car was only doing 580mph at this point. We had a small safety margin to play with, so I counted another 2 seconds, hit 600mph and then throttled back.

The engine took a fraction of a second longer than usual to wind down: Rolls-Royce had warned us it might do this at high speeds. Despite this, I only saw a peak speed of 608mph in the cockpit.

All good so far. In fact, up to this point, the run had been pretty much perfect. You can see a compilation of the onboard footage in the video of our final run.

Skip Youtube post by Bloodhound LSR

Image Copyright Bloodhound LSR
Bloodhound LSR

To give you some idea of what I’m doing, here’s a breakdown of the run in 10-second chunks:

  • Zero seconds. RAF air traffic controller Jess Kinsman’s voice breaks through the noise of the jet engine: “Bloodhound, Control. Clear to Roll. Wind is Southerly 3, gusting 6mph”. Brakes off, right foot pushing the throttle pedal forward to the detent for max dry power. A small tweak of steering to straighten the car up, already doing 30mph, check the engine is at max dry, select max reheat, which lights almost immediately. The car is already doing 100mph.
  • 10 seconds – 120 mph. The car is accelerating at full power, adding another 20mph to the speed every second. The power from the EJ200 jet engine is just awesome. At just over half a mile from the start, the car hits the filled-in ruts of the “old” road across our track at Hakskeen Pan, already doing 180mph. The suspension soaks up the bump, the only one I’ll feel during the whole run thanks to the amazing work of the local population in preparing the world’s best high-speed race track.
  • 20 seconds – 290mph. Above 200mph, the car starts to slide around more and more, as the high-speed metal wheels begin to “plane” over the hard mud surface. The light winds are enough to push the car around (you can see the movement in the video).
  • 30 seconds – 440mph. I’m still working at the steering to keep the car straight. On the audio you can hear me reminding myself to go “Easy on the steering” so I don’t risk making it worse. The car drifts right a little, as I let it yaw gently into the wind. Three miles into the run, the car crosses the old causeway road at 500mph, with barely a blip of movement through the chassis. •40 seconds – 550mph. As the drag builds up, the acceleration slows down a little, but we’re still putting on 10mph every second. I’m punching in steering inputs of up to 30 degrees each way, with much quicker movements needed at the higher speeds. The car gets to km 7 showing 580mph in the cockpit. I count another two seconds.
  • 50 seconds – 600mph. The moment the needle touches the “6” mark, I throttle back. The engine lag is noticeable. In my head I’m already running through the first steps of the emergency shutdown drill, just in case, when it starts to wind down less than one second later. As soon as the car settles at idle thrust, I reach down with my left hand to pull the lever for Chute 1. A short pause, then a “thump” as the chute hits us with an extra six tonnes of drag. The speed falls off very quickly now: losing 100mph takes less than 4 seconds.

Image copyright
Bloodhound LSR

Image caption

Good chute!

  • 60 seconds – 420mph. One minute after releasing the brakes, the car is slowing down through 400mph. The steering is settling down, helped by the rock-steady performance of the brake chute, and I can follow the line very accurately from now on. The end of our 10-mile race track is now less than 3 miles away, but we’ll stop with plenty of distance to spare.
  • 70 seconds – 280mph. As the car slows down to 250mph, I get ready to ease the wheel brakes on with my left foot. Applying exactly 45 Bar of hydraulic pressure (that’s a fairly firm press on the brake pedal) will give us optimum brake performance. Let’s not forget that we’re still doing 250mph though, in a six-tonne car, so it’s going to take about 25 seconds to stop after I put the brakes on.
  • 80 seconds – 180mph. Not much left to say. After driving at over 600mph, it feels like I can get out and walk at this point. After the car stopped, the data showed a peak speed of 628mph, about 20mph faster than I thought (and of course over 20mph faster than I was aiming for).

If I look a little perplexed in the video of the run, then that’s why. I assumed that the slightly slow engine wind-down had caused at least some of this difference, but a full 20mph? That’s over two seconds of full-power acceleration at 600mph. I couldn’t understand it.

A longer look at the data after we got back to our Tech Camp, plus reviewing the cockpit video frame-by-frame, gave me the answer. The GPS speedo had “jumped” by 20mph during the run, as one of the three onboard GPS feeds gave a poor signal (this is one of the reasons why the Land Speed Record is measured with external timing lights and not onboard GPS).

It’s an unusual fault, but an easy one to fix with a software filter. Another “win” for the high-speed testing. Despite the small GPS glitch on the last run, the end result was a fabulous one.

We went out to South Africa hoping to get the car over 600mph and, if there was enough performance left, to touch 1,000km/h if we could. 628mph, our peak speed, equates to 1,010km/h – job done!

A perfect end to a great high-speed test session.

As our Operations Director, Stuart Edmondson, says in the same video: “This car is absolutely ready for Land Speed Record speeds!” Quite so.

Image copyright
Bloodhound LSR